Metalworking Machinery Breakdown, Repair
Metalworking Machinery, Breakdown, Repair
In the event of a metal working machinery breakdown, our service team are available to attend your workshop, 1st determine the problem, then advise you on the repair required, arrange the location and supply of any required replacement parts,
returning to your workshop with replacement parts to effect the repair.
Repair Fibre Laser, Repair Plasma Machine, Repair Hydraulic Press Brake, Repair Electric Press Brake, Repair Hydraulic Guillotine, Repair Mechanical Guillotine Direct Drive , Repair Hydraulic Press, Repair Horizontal Press Brake, Repair Universal Steelworker, Repair Horizontal Bandsaw, Repair Pillar Drill, Repair Geared Head Pillar Drill, Repair Lathe, Repair Milling machine, Repair Horizontal Borer
We have a possibly the largest dealer metalworking machinery service team in the UK.
All our charges, terms and conditions are clearly shown here.
Metalworking machinery we routinely attend for breakdown, repair:
Breakdown Hydraulic metal cutting guillotines
Breakdown Mechanical DD Metal Cutting Guillotine
Breakdown Hydraulic Synchronised CNC press brakes
Breakdown Electric Press Brakes
Problems with NC & CNC Controls: Cybelec, Delem, Esa, Elgo
Breakdown HSG Fibre Laser
Breakdown CNC Punching Machine (servo electric)
Breakdown Hydraulic Corner Notcher
Breakdown Tube Bending Machine
Breakdown Universal Steelworker
Breakdown Plate Bending Roll
Breakdown Sheetmetal Bending Roll
Breakdown Horizontal Bandsaw
Breakdown Hydraulic Press
Breakdown Sheet Rolling Machine, NC & CNC
Breakdown Hydraulic Section Roll
Breakdown Powered Box & Pan Folder
Breakdown Centre Lathe Milling Machine, Radial & Pillar Drill
Breakdown Welding Positional Equipment
All our charges, terms and conditions are clearly shown here.
Here is a small glimpse of typical repair work:
- Start up, no power, no display
- We are experienced with many CNC & NC control systems, such as: Cybelec, Delem, Eurogauge, Elgo, Esa, we can diagnose faults and effect repairs usually involves removal of CNC unit to allow diagnostic testing on our equipment
- We are regularly asked to re calibrate one or more axis for a CNC metal working machine
- Axis drive problem, repair or replace axis drive cards
- CNC metal working machine lost operating parameters, due to operator error or back up battery failure
- Axis drive belt snaps, locate and fit replacement, then re calibrate the affected axis
- Tooling clash, requiring re setting of all axis & parameters
- Reset Press brake tooling to obtain a consistent bend angle, along tooling length, which involves resetting crown / camber of the top tooling
- Operator safety systems | Infra red front or Laser operator guard faults, electronic rear entry guarding,
infrared perimeter barriers | We are recognized SICK infra red guard installer - Metal cutting guillotines, re calibrate backgauge
- Re-gas a metal cutting guillotine return springs – gas return spring
- Hydraulic corner notcher’s, fit new foot pedal, replace or re-grind blades
- Replacement or refurbish machine screws and nuts, acme thread or ball screws
- Horizontal bandsaws, Bow Not descending, Drive wheel to be replaced
- Leaking Y1 + Y2 hydraulic cylinders – Strip & fit new seals
- Guillotine backgauge out of line, re set & calibrate
- Chipped or blunt guillotine blades – turn or re-grind the guillotine blades
Metalworking Manufacters we routinely work on
Breakdown, Repair of
RICO, HSG, LVD, AMADA, TECHNA-FAB, KINGSLAND,
HACO, TRUMPF, DURMAZLAR,
EDWARDS PEARSON, GASPERINI, ADIRA, SAFAN-DARLEY,
DENER, MG srl, DAVI, FACCIN, ROUNDO, FMB, RUSCH, BOWMAR, BALEIGH, BEHRINGER, PROMICAM, PRIMA POWER,
ERMAKSAN, CIDAN, BAKAYAL, MORGAN RUSHWORTH,
STEFA, HAMME, ESPRIT.
